Small cast aneroid knob traditional pattern
|
 |
Pocket style winder set knob (often used by N & Z) cast brass
|
|
Fusee chain and fine linkage arm joined approx 20mm of chain and 30mm linkage
|
|
Fusee chain for aneroid barometers. sold per cm almost any length. Suitable for pencil link found in many Large Self recording Aneroids (the Station type Clock and Barometer pieces) as well as many other aneroid repairs.
Size is 1mm links, .35mm wide and .5mm high. Very steady hands and eye glasses needed to assemble and use!
|
|
Bourdon key, blank, undriled, cast brass
|
|
|
|
Aneroid 'C' spring, 60mm wide, overall height 21mm, 2 holes
|
|
Aneroid capsule, 2 1/2" o/d, top spigot 3/4", bottom spigot and thread 3/8", overall height 1 1/4" The top spigot undrilled for retaining pin so you can drill in position that best suits the movement being repaired according to strength of spring and size of movement etc. Use of pressure chamber normally required to re-calibrate movement to dial range.
|
|
Aneroid capsule, 2 5/8" o/d, top spigot 3/4", bottom spigot and thread 3/8", overall height 1 1/4" The top spigot undrilled for retaining pin so you can drill in position that best suits the movement being repaired according to strength of spring and size of movement etc. Use of pressure chamber normally required to re-calibrate movement to dial range.
|
|
Aneroid capsule, 3 3/4" o/d, top spigot 3/4", bottom spigot and thread 3/8", overall height 1 1/2" The top spigot undrilled for retaining pin so you can drill in position that best suits the movement being repaired according to strength of spring and size of movement etc. Use of pressure chamber normally required to re-calibrate movement to dial range.
|
|
Pocket barometer capsules 1 1/8" o/d, 3/16" thick with 7/32" top spigot. The top spigot is drilled for retaining pin. Use of pressure chamber normally required to re-calibrate movement to dial range.
|
|
Pocket barometer capsule 1" diam (26mm) 2.5mm thick plus 2.5 mm long thread (2.5metric thread). Matt silver finish, soldered sides and evacuation spigot, total hieght 10mm. The top spigot undrilled for retaining pin so you can drill in position that best suits the movement being repaired according to strength of spring and size of movement etc. Use of pressure chamber normally required to re-calibrate movement to dial range.
|
|
Pocket barometer capsule 3/4" diameter (20mm) total height 7mm with 2mm metric thread at base. Matt silver finish, soldered sides and evacuation spigot capsule approx 2mm thick. The top spigot undrilled for retaining pin so you can drill in position that best suits the movement being repaired according to strength of spring and size of movement etc. Use of pressure chamber normally required to re-calibrate movement to dial range.
|
|
Aneroid capsule, 2 5/8" o/d, nickel plated, top spigot 3/4", bottom spigot and thread 3/8", overall height 1 1/4" The top spigot undrilled for retaining pin so you can drill in position that best suits the movement being repaired according to strength of spring and size of movement etc. Use of pressure chamber normally required to re-calibrate movement to dial range.
|
|
Double aneroid capsule, 3" diameter, flange type, tinned finish. The top spigot undrilled for retaining pin so you can drill in position that best suits the movement being repaired according to strength of spring and size of movement etc. Use of pressure chamber normally required to re-calibrate movement to dial range.
|
|
Double aneroid capsule, 2 3/4" diameter, flange type, tinned finish .The top spigot undrilled for retaining pin so you can drill in position that best suits the movement being repaired according to strength of spring and size of movement etc. Use of pressure chamber normally required to re-calibrate movement to dial range.
|
|
Dent type Aneroid Capsule, 2 3/4" diameter 5/32" thick plus thin threaded brass base connector and special slotted Dent top spigot 1/2" diameter 5/8" tall made specially for the early Dent brass cased aneroids.
|
|
Aneroid capsule, 2 1/8" o/d, nickel plated, top spigot 3/4", bottom spigot and thread 3/8", overall height 1 5/16" The top spigot undrilled for retaining pin so you can drill in position that best suits the movement being repaired according to strength of spring and size of movement etc. Use of pressure chamber normally required to re-calibrate movement to dial range.
|
|
Aneroid capsule, 1 7/8" o/d, threaded top spigot 3/16" & bottom, overall height 1/2" (by you making a brass spigot to fit thread these can normally be made to suit continental style barometers with open movements.) Use of pressure chamber normally required to re-calibrate movement to dial range.
|
|
Aneroid capsule, 1 1/4" o/d, threaded top spigot 5/32", threaded bottom spigot 1/8" (by you making a brass spigot to fit thread these can normally be made to suit continental style barometers with open movements.) Use of pressure chamber normally required to re-calibrate movement to dial range.
|
|
Dolls house barometer, 2" x 3/4", soft cast metal (not a childs toy)
|
|
